.

Release Note
C0FE0029_xxxx.sff

MPI Version
FPGA Version
04.00.00
Production Release
C0FE0029_0500
03.04.00
Production Release
C0FE0029_0400
03.03.00
Production Release
C0FE0029_0346
03.02.00
Production Release
C0FE0029_0345
03.01.01
C0FE0029_0311
03.01.00
Production Release
C0FE0029_0311

  Table of Contents
     
    Changes and Bug Fixes
     

C0FE0029_0500
     sqMac upgraded to support 64 nodes - New Feature - FP886
     Improved Capture module unified with Probe features - General Change - FP823

C0FE0029_0400
     Remove drive reset complete from the fault and fault mask registers - General Change - FP466 
     The watchdog fault was incorrectly being cleared after being activated - Bug Fix- FP465
     sqMac Version 0300 - New Feature - FP407
     Latch added on the notAmpPowered bit - General Change - FP402
     Support for a maximum count rate of 50MHz without filters - New Feature - FP337

C0FE0029_0346
     Modifications to gpioPinConfigReg - General Change - FP336
     Intermittent Dual String Discovery failure - Bug Fix - FP332
     sqMac - 0x00 will be read for dataType NULL - New Feature - FP323
     Intermittent Fault Recovery failures - Bug Fix - FP315

C0FE0029_0345
     Pulse count sample problem with missed packets - Bug Fix - FP291

C0FE0029_0340
     New BranchRev Register - New Feature - FP231

C0FE0029_0341
     sqMac rxMiiBuffer multiple packets - General Change - FP263
     sqNode adcAd977 double buffer - General Change - FP260

C0FE0029_0311
     sqNode C0FE0029: removal of compare features - General Change - FP175
     Expansion of dedicatedIo to 32 bits - General Change - FP167
     Clearing driveWatchdogFault and the driveChecksumError - Bug Fix - FP160
     Set unused pin default to FLOAT - General Change - FP155

C0FE0029_0303
     SqMac Cyclic Status - Bug Fix - FP141
     Support for Multi-Vendor Flash Download - General Change - FP140
     NodeDisable and analogPowerFault invert - Bug Fix - FP139
     PhaseAdjust clash - Bug Fix - FP137
     24mA drive for GPIO pins - General Change - FP134
     SqMax rcvDataUnload - Bug Fix - FP123
     Improved Secondary Encoder Support - General Change - FP109
     Improved ADC Support - General Change -FP108


C0FE0029_0500

  sqMac upgraded to support 64 nodes
    Reference Number: FP 886
    Type: New Feature
    FPGA Version: 0x0500
   

Description

The sqMac module (the network interface logic) was upgraded to support up to 64 nodes. Key changes include:

larger packet forwarding buffer. Previously 128 bits deep, now 2048 bits (Spartan2/2e) or 8196 bits (Spartan3/3e).

Improved support for pipelined service commands.


  Improved Capture module unified with Probe features
    Reference Number: FP 823
    Type: General Change
    FPGA Version: 0x0500
    Description:

A new unified Capture module was created to replace the older versions of both the Capture and Probe modules. In addition, new trigger features were introduced.

All Capture modules have a base feature set: Single-shot capture with the new trigger select, pre-trigger condition, and filter options. This Single-shot capture replaces the basic capture in prior FPGA versions. Some FPGAs support an additional Auto-arm mode. When enabled by software, Auto-arm uses a capture buffer memory to store multiple capture events (replaces the Probe module in prior FPGA versions).

The new trigger logic is common to all FPGAs (and slightly different to prior FPGA versions). Up to 32 trigger source inputs are available. The exact set of trigger source signals depends on the IO for each node. A trigger event can be selected from any input, with rising, falling, or both edges active. An optional filter function can be used to deglitch the signal. An optional pre-condition (based on the same trigger sources) can be specified: pre-condition high, low, rising edge, falling edge, or both.

For more information about using the new capture features, see Capture Objects.

 

C0FE0029_0400

  Remove drive reset complete from the fault and fault mask registers
    Reference Number: FP 466
    Type: General Change
    FPGA Version: 0x0400
    Problem/Cause:
As more drives require a driveBootComplete bit to indicate when they are finished booting, it was necessary to change the current bit to a more ideal location.
   

Fix/Solution:
The FPGA bit, driveResetComplete, has been removed from the dedicatedIo Fault and Fault Mask registers. This bit has been replaced with driveBootComplete in the dedicatedIo Config register. This bit is monitored solely by the sqNodeLib utility. It is currently not visible through MPI calls or through Motion Console.
NOTE: This change causes compatibility issues between new FPGAs and old software (or old FPGAs with new software). FPGA version x0400 and later require the 03.04.00 MPI software release and later.


  The watchdog fault was incorrectly being cleared after being activated
    Reference Number: FP 465
    Type: Bug Fix
    FPGA Version: 0x0400
    Problem/Cause:
The Slice I/O watchdog fault was incorrectly being cleared after being activated. If a watchdog fault occurred, the FPGA would send a stop command to all slices to halt cyclic operation. As a result of being in this stop mode, it would cause the watchdog fault to be disabled and incorrectly clear itself. Therefore, the fault would never be seen.
   

Fix/Solution:
The FPGA was changed so that if the watchdog fault was the trigger to enter into the stop mode, the watchdog fault would not disable itself, thus allowing the fault to stay latched and also trigger the nodeIo fault.


  sqMac Version 0300
    Reference Number: FP 407
    Type: New Feature
    FPGA Version: 0x0400
   

Description:
The sqNode x0400 FPGA release introduces an upgraded network module, sqMac version 0300. Upgraded features include:

  • SynqNet HotReplace - allows one or more more nodes to be shutdown, replaced, and brought back on-line without interrupting other nodes.
  • Revised Cable Length Discovery - a new node-to-node method was added to make discovery more accurate.
  • sqPll shutdown - a controlled shutdown of individual nodes for HotReplace.

The sqMac 0300 version is NOT fully compatible with MPI versions prior to 03.04.00. Using 0300 sqMac with older software (for some configurations) might cause the "idle cable" check function to accidently corrupt normal packet traffic. But, the MPI will issue a warning if old/new FPGA/MPI are mixed by accident.


  Latch added on the notAmpPowered bit
    Reference Number: FP 402
    Type: General Change
    FPGA Version: 0x0400
    Problem/Cause:
In FPGA versions previous to 0x0400, the notAmpPowered fault bit was not latched.
   

Fix/Solution:
In FPGA versions 0x0400 and later, the notAmpPowered fault bit is now latched. If active, it can be cleared by writing a "1" to bit 5 of the dedicatedIo fault status register.


  Support for a maximum count rate of 50MHz without filters
    Reference Number: FP 337
    Type: New Feature
    FPGA Version: 0x0347; 0x0400
   

Description:
In FPGAs 0x0347, 0x0400, and later, the maximum quadrature encoder count rate has been improved to be 50MHz. In previous FPGA releases, the maximum count rate was 25MHz.

 

C0FE0029_0346

  Modications to gpioPinConfigReg
    Reference Number: FP 336
    Type: General Change
    FPGA Version: 0x0346
    Problem/Cause:
Prior to FPGA version x0346, gpio pins that were configured as an "output" did not resume "output" direction after an ioAbort event. Also, during the ioAbort event, if a service channel write to the gpio configuration register occurred, the gpio "output" pins would be set to "output" mode momentarily (and then cleared to "input" mode by the ioAbort event). After the ioAbort event was cleared, the gpio pin state would remain as in "input" mode unless software restored the gpio configuration register again.
   

Fix/Solution:
In FPGA version x0346 and later, an ioAbort event still forces gpio "output" pins to "input" mode, which allows external resistors to pull pins from either high or low for a "safe" state. The resistors may or may not be present depending on the PCB assembly. However, during an ioAbort event, service writes to the gpio configuration register no longer cause momentary "output" direction. After the ioAbort event is cleared, gpio pins will resume their previous "output" state without software intervention.


  Intermittent Dual String Discovery Failure
    Reference Number: FP 332
    Type: Bug Fix
    FPGA Version: 0x0346
    Problem/Cause:
Probe, resetRequest, and resetComplete were repeated on the wrong port (OUT port) when using the OUT port as the primary port during SynqNet node discovery. As a result, SynqNet node discovery may have failed. This problem was caused by the probe, resetRequest, and resetComplete being repeated on the wrong port. This issue existed in all FPGA versions prior to x0346.
   

Fix/Solution:
The FPGA code was corrected in version x0346 and later releases. This fix is required for systems using the Dual String or IN Port String topologies. This fix is NOT required for systems using normal OUT Port String or Ring topologies.


  sqMac - 0x00 will be read for dataType NULL
    Reference Number: FP 323
    Type: New Feature
    FPGA Version: 0x0346
   

Description:
0x00 will be read for dataType NULL in the status and feedback packets.


  Intermittent Fault Recovery failures
    Reference Number: FP 315
    Type: Bug Fix
    FPGA Version: 0x0346
    Problem/Cause:
Some nodes may have intermittently failed to recover from a fault in some network configurations. If a node failed to recover, it exited cyclic operation and correctly triggered ioAbort logic (forcing outputs into "safe" states). Any nodes "downstream" of the failing node (after it switched ports) were also likely to exit cyclic operation. For any given node, there was only a small schedule window where this error may have occurred. There were two causes of the problem. The rcvMiiBuffer did not clear itself after an overflow in some situations. Also, a packet fragment generated by the fault recovery that happened to have valid CRC (but no data) would confuse the packetFifo, and corrupt internal node configuration bits. The first issue existed in FPGA build versions x0341 through x0345 and their branches (MPI release 03.02.00). The second issue existed in all FPGA versions prior to x0346.
   

Fix/Solution:
The fault recovery problems was corrected in FPGA build versions x0346 and later. The rcvMiiBuffer will correctly clear itself after an overflow. The xmitMiiReg will release xmitHoldRcvBuf within 8 clocks after a fault, preventing an rcvMiiBuffer overflow. 8 clocks will guarantee that there is minimum packet spacing between the packets. sqPll will ignore the second SYNQ packet after fault recovery (in case packet delays were effected in the cycle where fault recovery occurred). The rcvMii will correctly handle a valid packet with data length of 0. No software changes are required.



C0FE0029_0345

  Pulse count sample problem with missed packets
    Reference Number: FP 291
    Type: Bug Fix
    FPGA Version: 0x0345
   

Problem/Cause:
The pulse engine (step/direction logic) may appear to have a momentary position error after network packet errors (or fault recovery). The FPGA pulseFeedback value was not updated when DEMAND packet errors occurred. The "old" pulseFeedback value was sent back to the controller until valid DEMAND packets arrived, which may look like zero velocity to the controller. If a fault recovery is in progress, and the controller does not receive the FEEDBACK packet, the controller will interpolate the expected position based on constant velocity, then at the end of recovery, the controller may get one FEEDBACK packet with "old" pulseFeedback position (correct pulseFeedback will arrive in subsequent packets). This issue existed in all FPGAs prior to version x0345.

   

Fix/Solution:
The FPGA code was corrected in versions x0345 and later. No software changes are required.

 

C0FE0029_0340

  New BranchRev Register
    Reference Number: FP 231
    Type: New Feature
    FPGA Version: 0x0340
   

Description:
Add BranchRev register. This extends the existing 16 bits of FPGA version number with 8 bits of branch and 8 bits of revision ID.

 

C0FE0029_0341

  sqMac rxMiiBuffer multiple packets
    Reference Number: FP 263
    Type: General Change
    FPGA Version: 0x0341
   

Description:
Add support for multiple packets to the rxMiiBuffer. This improves tolerance to network jitter. Prior to version x0341, the rxMiiBuffer could absorb up to 32 clocks (1.28 µS) of delay for a single packet, but only 8 clocks for multiple packets with minimum spacing. This change is required to meet theoretical worst-case network jitter in large networks (32 nodes). The improvement may also help at network startup, since the node's PLL phase error is larger than normal (as the PLL pulls into nominal lock). No software changes are required.


  sqNode adcAd977 double buffer
    Reference Number: FP 260
    Type: General Change
    FPGA Version: 0x0341
   

Description:
Add double-buffering to the ADC input data. This change eliminates the need for a SynqNet scheduling limit (and the corresponding software error check). Prior to version x0341, a software error check prevented operation if the controller cycle time was less than the time required to complete the full ADC read sequence of all enabled channels. Otherwise, there would be a chance that packet data might be sent while new ADC data was arriving. This might result in some data from the "new" ADC read, and some data from the "old" (previous) read. If one 16-bit ADC value contained 8 bits of "old" and 8 bits of "new" data, this could cause an invalid value. For version x0341 and later, the ADC read data is double-buffered to prevent the possibility of bad data. If the controller cycle is faster than the ADC cycle, the node will send "old" data in multiple packets while the ADC cycle completes, then switch to "new" data.

NOTE: For existing systems, with controller cycles longer than ADC cycles, there is no change in ADC behavior. However, for new systems (with new MPI releases) it is possible to use higher controller rates without reducing the number of enabled ADC channels.

New FPGAs (x0341 and later) are fully backwards compatible with old MPI software releases. New MPI releases (starting with 03.02.xx) are generally compatible with old FPGAs (prior to version x0341). However, the former error check for ADC cycle period has been eliminated, so it is possible to configure a controller cycle rate fast enough to cause a problem when using old FPGAs with new MPI.

 

C0FE0029_0311

  sqNode C0FE0029: removal of compare features
    Reference Number: FP 175
    Type: General Change
    FPGA Version: 0x0311
   

Description:
C0FE0029 no longer supports compare. This feature was deleted due to lack of FPGA space.

NOTE: The MPI does not yet support compare, so this does not affect existing systems.


  dedicatedIo - Expansion of dedicatedIn to 32 bits
    Reference Number: FP 167
    Type: General Change
    FPGA Version: 0x0311
   

Description:
Expand the dedicatedIn word from 16 bits to 32 bits and add the status bits Feedback 0 Fault and Feedback 1 Fault. Note: Although the FPGAs now supports additional bits, the MPI does not yet enable them.


  Clearing driveWatchdogFault and driveChecksumError
    Reference Number: FP 160
    Type: Bug Fix
    FPGA Version: 0x0311
   

Problem/Cause:
Clearing the driveWatchdogFault and driveChecksumError required two service comands—a write to start the clear, and a write to end the clear. MPI releases prior to the 03.01.00 did not clear the bits.

   

Fix/Solution:
Corrected the Drive Watchdog Fault and Drive Checksum Error bits to clear with a single service command. MPI releases 03.01.00 and later support this new behavior and clear the bits after a network reset.


  Set unused pin default to FLOAT
    Reference Number: FP 155
    Type: General Change
    FPGA Version: 0x0311
   

Description:
Set unused pins to FLOAT after the FPGA configuration process. After a power-on, but prior to FPGA configuration, SynqNet FPGA pins should be high-impedance outputs.

NOTE: The mode pins can enable internal pullups, but this is not recommended for SynqNet.

After configuration, unused pins will be high-impedance outputs with no internal pull-up or pulldown. In earlier versions, unused pins would default to weak internal pulldowns. This was not ideal since it could have conflicted with an external pull-up.

 

C0FE0029_0303

  SqMax Cyclic Status
    Reference Number: FP 141
    Type: Bug Fix
    FPGA Version: 0x0303
   

Problem/Cause:
There was a problem where SqMax NodeStatus cyclic status bits may have been corrupted after reading some of the FPGA registers (via the service command). The bits that could have been corrupted are: analogPowerFault, ioAbort, nodeAlarm, and nodeDisable. This issue has existed since release x0100.

   

Fix/Solution:
This problem has been fixed.


  Support for Multi-Vendor Flash Download
    Reference Number: FP 140
    Type: General Change
    FPGA Version: 0x0303
   

Description:
Support has been added for a number of different flash component vendors. Flash components that are currently supported are:

Vendor
PN
Size
Circuit
Atmel
AT25F2048N-10SI-2.7 (2MB)
2MB
Bowsprit
Atmel
AT45DB021B
2MB
Bowsprit
Atmel
AT45DB041B
4MB
Bowsprit
Atmel
AT45DB081B
8MB
Bowsprit
NEXFLASH
NX25P20-VN
2MB
Bowsprit
NEXFLASH
NX25P40-VN
4MB
Bowsprit
SST
SST25VF020-20-4C-SA
2MB
Bowsprit
SST
SST25VF040-20-4C-SA
4MB
Bowsprit
STM
M25P20-VMN6T
2MB
Bowsprit
STM
M25P40-VMN6T
4MB
Bowsprit
STM
M25P80-VMN6T
8MB
Bowsprit
Xilinx
XC18V02
2MB
Outrigger

  NodeDisable and analogPowerFault invert
    Reference Number: FP 139
    Type: Bug Fix
    FPGA Version: 0x0303
   

Problem/Cause:
There was a problem with the inverted polarity option for the FPGA inputs nodeDisable and analogPowerFault. Prior to this fix, only the default polarity was functional. The problem happened because the hardware invert logic was inserted after the hardware latch function. Therefore, when "invert" was selected, the input would typically latch the negated state, and would not report a fault unless the latch was cleared by a software command. If the "invert" option was NOT used, the input would function correctly. This issue did not exist until the x020C release, where these inputs were first latched.

   

Fix/Solution:
This problem has been fixed.


  PhaseAdjust clash
    Reference Number: FP 137
    Type: Bug Fix
    FPGA Version: 0x0303
   

Problem/Cause:
There was a problem in the sqPll function of the sqMac. With certain timing values, one node in the network may have fail to hold lock and then aborts cyclic operation. For a typical 3-node network, this timing typically occurred with TxTime set to 95%. Other TxTime values may fail in other network configurations.

   

Fix/Solution:
This problem has been fixed.


  24mA drive for GPIO pins
    Reference Number: FP 134
    Type: General Change
    FPGA Version: 0x0303
   

Description:
The drive current of GPIO pins has been increased to +/-24mA. Other outputs which may drive opto isolators (LED outputs, nodeAlarm, ampEnable, brakeApplied) were already configured for 24mA drive current. See individual FPGA specifications for complete details of I/O characteristics.


  SqMax rcvDataUnload
    Reference Number: FP 123
    Type: Bug Fix
    FPGA Version: 0x0303
   

Problem/Cause:
There was a problem in the receive data unload function of the sqMax. In certain situations where the packet size did not match the configured packet size, invalid sqMax outputs were observed to cause "glitches" in the I/O output signals. The glitches would occur at the transition from cyclic to asynq operation, but the ioAbort signal would normally prevent these glitches from reaching external logic.

   

Fix/Solution:
This problem has been fixed.


  Improved Secondary Encoder Support
    Reference Number: FP 109
    Type: General Change
    FPGA Version: 0x0303
   

Description:
Improvements have been made to the secondary encoder features. These changes allow the use of encoder faults and capture with secondary encoders. Secondary feedback for drives has also been added. The changes are NOT backwards compatible with software releases prior to 20031222 (secondary encoder feedback is not fully functional with prior software).


  Improved ADC Support
    Reference Number: FP 108
    Type: General Change
    FPGA Version: 0x0303
   

Description:
Improvements have been made to the ADC features to use the new "nodeIo" conventions. These changes allow up to 8 ADC channels per node (prior to this, the default was 1 ADC channel per motor). The changes are NOT backwards compatible with software releases prior to 20031222 (ADCs are not functional with prior software).

 

       Legal Notice  |  Tech Email  |  Feedback
      
Copyright ©
2001-2021 Motion Engineering